Dr. Jaby Mohammed

Dr. Jaby Mohammed

Associate Professor, Industrial and Systems Engineering Department

Dr. Mohammed is an Assistant Professor in the STEPS program at the PI. Prior to his position at PI, he was the Director for the graduate program in Technology and an Assistant professor at Purdue University (Fort Wayne campus). He also has worked at Morehead State University as an assistant professor after his PhD from University of Louisville. He is also an engineering faculty with the Kentucky governors scholar program for the years 2006-2009.Dr. Mohammed is a senior member of the Society of Manufacturing Engineers (SME) and Institute of Industrial Engineers (IIE). His area of research includes New Product development and Rapid prototyping; supply chain management, six sigma, and lean Manufacturing. He has conducted applied research in the area of laser cladding and rapid prototyping using DMD and SLS machines. His research had been sponsored by the Water furnace International, Kentucky science and engineering foundation (KSEF), Technical assistance program from the state of Indiana (TAP), Institute of regional analysis and public policy (IRAPP) at Morehead State University. He has published technical papers in handbooks, journals and conference proceedings. He has mentored six graduate MS students on their thesis. His teaching interests are in the area of quality control, project management, and engineering education

Address: Abu Dhabi UAE

Telephone: +971-2-607-5297 (Bu Hasa) and 607-5696 (Arzanah)

Email: jaby.mohammed@ku.ac.ae

  • Ph.D., Industrial Engineering, University of Louisville, KY, USA 2006
  • MS, Industrial Engineering, University of Louisville, KY, USA 2003
  • MBA, Operations Management, IGNOU, India, 2000
  • B-TECH, Mechanical Engineering, University of Kerala, India 1997

Selected Publications / Conference Proceedings / Abstracts

  1. Alavizadeh, A., Djvanshir, R., Tarokh, M., and Mohammed, J., 2012. “Agile value creation and co-evolution in global supply chains,” in Customer-Oriented Global Supply Chains: Concepts for Effective Management, E. Eyob and E. G. Tetteh, (Eds.), Hershey, PA, USA, IGI Global, pp. 94-111.

  2. Mohammed, J., 2012. “Application of fuzzy system and intelligent control for improving DMD process”, International Journal of Engineering Research and Innovation, vol. 4-1, pp. 34-39.

  3. Mohammed, J., Dimmit, N., 2012. “A coursework plan for improving skills necessary for successful capstone projects,” Proc. American Society of Engineering Education annual conference and Exposition, San Antonio, TX, USA.

  4. Mohammed, J., 2012. “Teaching freshmen engineering design via hybrid mode: A case study in the Middle East,” Proc. American Society of Engineering Education annual conference and Exposition San Antonio, TX, USA.

  5. Dimmit, N., Mohammed, J., Moore, D., 2012. “Strategies for improving technical communication effectiveness skills in a Middle East Engineering Program,” Proc. American Society of Engineering Education annual conference and Exposition San Antonio, TX, USA.

  6. Cubero, S. N., Billingsley, J., and Mohammed, J., 2011. “Mechanical design of an amphibious walking and swimming robot,” Proc. 18th International Conference on Mechatronics & Machine Vision in Practice (M2VIP), Brisbane, Australia.

  7. Mohammed, J., and Sadique, A., 2010. “Lean value stream manufacturing for sustainable manufacturing,” Proc. 8th Global conference on sustainable manufacturing, Abu Dhabi, UAE.

  8. Mohammed, J., Nawaz, S., and Pablo, R. 2010. “Implementing lead course contents in bachelors curriculum,” Proc. American society of engineering education, Louisville, KY, USA.

  9. Mohammed, J., Albayari, J., and Narang, R. 2010. “Developing a new manufacturing engineering technology curriculum”, in Proceedings of the American Society of Engineering Education, Louisville, KY, USA.

  10. Nepal, B., Mohammed, J., Albayari, J., and Lin, P. I., 2010. “Program assessment and continuous improvement plan for Master of Science in technology,” Proc. American Society of Engineering Education, Louisville, KY, USA.

  11. Mohammed. J, Ali Alavi, “ Project Quality and Risk Management”, Handbook of Research on Technology Project Management, Planning, and Operations, ISBN 978-1-60566-400-2 (2009)

  12. Mohammed. J, ” Technology Management by Objectives”, Handbook of Research on Technology Project Management, Planning, and Operations, ISBN 978-1-60566-400-2 (2009)

  13. Mohammed. J., May,J., “ Applying axiomatic design and knowledge based engineering to a plastic drum design”, Proceedings for the 2009 ASEE annual conference, June 22-25, 2008, Austin, TX ( Available on CD)

  14. Mohammed, J., May, J., Alavi, A., 2008, “Application of Computer Aided Design in Knowledge Based Engineering” International association of Journals and conferences, November 18 – 22, 2008, Nashville, Tennessee, ISSN 1930-6628(2008)

  15. Mohammed. J., Mason. S, Xialong. Li, “ Departmental survival through collaborative industrial partnership” Proceedings for the 2008 ASEE annual conference, June 22-25, 2008, Pittsburg, PA ( Available on CD)

  16. Gabriel. A, Mohammed. J., Yuqui. You, “ Teaching engineering economy online in construction program”, Proceedings for the 2008 ASEE annual conference, June 22-25, 2008, Pittsburg, PA ( Available on CD)

  17. Mohammed, J.,“ Material Innovation for die casting molds”, Productions and operations management society 2007, Dallas,

  18. Mohammed, J.,“, “Manufacture of die casting Molds via DMD”, Society of manufacturing engineers rapid prototyping conference and exposition 2007, Detroit, MI.

  19. Mohammed, J.,“ Alexander, S., “ Defining coating material for aluminum die casting molds using laser cladding process”, Proceeding for the ICALEO 2006

  20. Mohammed, J., Alungbe, G., Zargari, A.,2007, “ First level technical management skills in rapid prototyping” Proceedings for the National Association of Industrial technology convention, Panama city, FL (2007)

  21. Mohammed, J., Mason, S., Patel, R., 2007,“ Application of Autodesk Inventor in solid modeling and analysis of MEMS / Nano structure” Proceedings for the National Association of Industrial technology convention, Panama city, FL (2007)

  22. Mason, S., Mohammed, J., Zargari, A., 2007,“ The status and demographics of industrial technology alumni” Proceedings for the National Association of Industrial technology convention, Panama city, FL

  23. Mohammed, J., 2007,Technical presentation for the Lexington SME chapter 154, presentation was titled,” Direct Metal Deposition (DMD)”, March 2007

  24. Mohammed, J., 2007,“Material matrix for die casting molds using laser cladding technique”, presented at the 92nd annual meeting of Kentucky academy of science, Morehead, KY, Nov 05-08, 2007.

  25. Mohammed, J., Zhang, J. , Alexander, S., 2005,Presented a poster for the third annual Kentucky Innovation and enterprise Conference, Louisville, KY ( March 2005)